升降平臺不能行走的故障解決方法。Solution to the failure of the lifting platform in Shijiazhuang.

1.先對升降平臺配件的升降平臺電池進行檢查看看有沒有電壓，如果電壓有的檢查電壓是不是能夠正常的使用。排除方法：電池沒有電壓或者是電壓太低的話直接對其電池進行充電。Lifting platform for the first part of the lifting platform to check the battery to see if there is no voltage, if the voltage is not checked for some of the normal use of Shijiazhuang. Method: the battery does not have the voltage or the voltage is too low, then directly charge the battery.

2.檢查鋁合金升降平臺配件升開關和線路有沒有松動或者是短路的現象，微動開關有沒有損壞。排除方法：維修和清理線路，更換或者是維修微動開關。Check the lifting parts of aluminum alloy lifting devices and circuits are loose or short circuit phenomenon, micro switch is not damaged. Methods: repair and clean the line, replace or repair the microswitch.

3.檢查升降平臺起升的接觸器總成有沒有燒壞或者是線圈短路和斷路，排除方法：維修接觸器的白金觸點或者是直接更換一個新的液壓接觸器總成。Shijiazhuang check the lifting platform lifting contactor assembly has not burnt coil or short circuit and open circuit, troubleshooting: maintenance of contactor platinum contact or direct replacement of a new hydraulic contactor assembly.

4.檢查起升的模塊有沒有燒壞或者是燒短路和斷路的現象，排除方法：維修或者是更換模塊總成。Check the lifting modules are not burnt or burnt short circuit and open circuit phenomenon, troubleshooting: repair or replace module assembly.

5.檢查升降平臺電機有沒有電壓到，檢查電機有沒有短路或者是斷路和漏電的現象，檢查碳刷有沒有嚴重的磨損等。排除方法：維修線路，更換電機的碳刷和維修電機的銅頭，維修電機總成或者是更換新的電機。Check Shijiazhuang lifting platform have motor voltage to the motor, check that there is no short circuit or open circuit and leakage phenomenon, there is no serious check brush wear. Troubleshooting: line maintenance, replacement and maintenance of motor brushless motor copper head, repair the motor assembly or replacement of the motor.

6.檢查鋁合金升降平臺配件液壓泵，多路閥，油管和油缸有沒有損壞，排除方法：液壓泵損壞維修或者是直接更換新的液壓泵總成，多路閥損壞對其進行維修或者是直接更換新的多路閥總成，更換新的液壓油管，油缸更換修理包或者是更換新的油缸總成。Check the Aluminum Alloy lifting platform hydraulic pump fittings, valve, pipe and cylinder are not damaged, troubleshooting: hydraulic pump damage repair or directly replace the new hydraulic pump assembly, maintenance or the direct replacement valve new assembly multiway valve is damaged, replace the new hydraulic oil cylinder replacement, repair the package or replacement of the cylinder assembly.

以上就是關于石家莊升降平臺不能行走的故障解決方法的介紹，升降平臺還可能出現其他的故障問題，因此，最好的辦法是在購買石家莊升降平臺時，選擇正規的廠商，一旦出問題能夠立刻修繕，這樣才是最好的辦法。The above is about the Shijiazhuang fault lifting platform can not walk solving method is introduced, the lifting platform may also occur in other fault problems, therefore, the best way is to buy Shijiazhuang lifting platform, choose the regular manufacturers, once the problem can be immediately repaired, this is the best way.